Browse Categories

SIKAFLEX 292 WHITE 300ML CARTRIDGE

SIKAFLEX 292 WHITE 300ML CARTRIDGE
Item #: 83814187

Product Info

409802
SIKA

SIKAFLEX 292 WHITE 300ML CARTRIDGE
Sika 409802 292 12ea 300ml Cartridges per case 86 cases per pallet Old Part # 801

Sikaflex®-292i is a non-sag 1-component polyurethane adhesive of thixotropic, paste-like consistency which cures on exposure to atmospheric moisture. It exhibits excellent adhesive properties and a good mechanical strength. Sikaflex®-292i meets the low spread of flame requirements set out by the International Maritime Organisation (IMO).

PRODUCT BENEFITS

  • Good gap-filling properties
  • Can be painted
  • Bonds well to a wide variety of substrates
  • Wheelmark approved
  • Solvent free and very low VOC

Areas of Application

Sikaflex®-292i is suitable for structural joints in marine constructions which will be subjected to high dynamic stresses. It is suitable to bond metals, particularly aluminium (including anodized finishes), metal primers and paint coatings (2-component systems), or ceramic materials, plastics such as GRP (unsaturated polyester resin), ABS, etc. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-292i on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.

Chemical base

1-component polyurethane

Color (CQP001-1)

White, black

Cure mechanism

Moisture-curing

Density (uncured)

depending on color

1.3 kg/l

Non-sag properties (CQP061-1)

Very good

Application temperature

10 - 40 °C

Skin time (CQP019-1)

40 minutes A

Open time (CQP526-1)

30 minutes A

Curing speed (CQP049-1)

(see diagram 1)

Shrinkage (CQP014-1)

2 %

Shore A hardness (CQP023-1 / ISO 7619-1)

50

Tensile strength (CQP036-1 / ISO 527)

3 MPa

Elongation at break (CQP036-1 / ISO 527)

600 %

Tear propagation resistance (CQP045-1 / ISO 34)

8 N/mm

Tensile lap-shear strength (CQP046-1 / ISO 4587)

2 MPa

Service temperature (CQP509-1 / CQP513-1)

4 hours

1 hour

-50 - 90 °C

120 °C

140 °C

Shelf life (CQP016-1)

12 months B

CQP = Corporate Quality Procedure

B) 23 °C / 50 % r. h.

C) storage below 25 °C

Surface preparation

Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.

Application

Sikaflex®-292i can be processed between 10 °C and 40 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.
Consider that the viscosity will increase at low temperature. For easy application, condition the adhesive at ambient temperature prior to use.

To ensure a uniform thickness of the bondline it is recommend to apply the adhesive in form of a triangular bead (see figure 1).

Sikaflex®-292i can be processed with manual, pneumatic or electric driven piston guns. The open time is significantly shorter in hot and humid climate. The parts must always be installed within the open time. Never join bonding parts if the adhesive has built a skin.

Tooling and finishing

Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use.

Removal

Uncured Sikaflex®-292i can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water.

Do not use solvents on skin.


Call for Pricing
NOT IN STOCK
UOM : EA
QTY:

Have Questions?

Ask our experts: